Water Pressure Transmitter
0bar~0.1bar…400bar
Accuracy: ±0.5%FS
Embedded LED Display
-
Products
- Solutions
- Service Support
Pages
- Pressure Sensor
- Pressure Transmitter and Transducer
- What is a Pressure Transducer？
- Level Transmitter and Sensors
- Differential Pressure Sensors
- Differential Pressure Transmitters
- Level transmitter for Fuel and Chemical
- Water Pressure Sensors
- Industrial Pressure Sensors and Transmitters
- Switches
- Liquid Pressure Sensors and Transmitters
- Company
High Pressure Range Pressure Sensor
MPM283II
- · Φ12.6x10.5mm
- · 0bar~1bar…1000bar
- · -10~80℃ Compensated
Used For
Gas & Liquid Pressure Measurement, Pressure Inspection Meter, Pressure Calibrator
Leave a MessageMPM283II
Used For
Gas & Liquid Pressure Measurement, Pressure Inspection Meter, Pressure Calibrator
Leave a MessageMPM283II high-pressure sensor for tank level is made of a diffused pressure sensing die and stainless steel 316L housing. With a corrugated stainless steel 316L diaphragm, the measured pressure is transmitted to the sensing die through it and internally filled silicon oil. By doing linear correction and temperature compensation, the stable performance of the pressure transducer is guaranteed. With NBR or EPDM O-ring, it is easy for users to install and applicable for different temperature application. The pressure range is 0bar ~ 2.0bar…1000bar and the dimesion is Φ12.6×10.5 mm.
Electrical Performance
• Power supply: ≤2.0mA DC
• Input impedance: 2kΩ~8kΩ
• Output impedance: 3.5kΩ~6kΩ
• Response (10%~90%): <1ms
• Insulated resistor: 100MΩ@100V DC
• Overpressure: 2 times FS or 1100bar (min. value is valid)
Image:
MPM283II high-pressure sensor for tank level is made of a diffused pressure sensing die and stainless steel 316L housing. With a corrugated stainless steel 316L diaphragm, the measured pressure is transmitted to the sensing die through it and internally filled silicon oil. By doing linear correction and temperature compensation, the stable performance of the pressure transducer is guaranteed. With NBR or EPDM O-ring, it is easy for users to install and applicable for different temperature application. The pressure range is 0bar ~ 2.0bar…1000bar and the dimesion is Φ12.6×10.5 mm.
Electrical Performance
• Power supply: ≤2.0mA DC
• Input impedance: 2kΩ~8kΩ
• Output impedance: 3.5kΩ~6kΩ
• Response (10%~90%): <1ms
• Insulated resistor: 100MΩ@100V DC
• Overpressure: 2 times FS or 1100bar (min. value is valid)
Read / Download our Datasheet in PDF
Download
- Related Products
- Related Accessories
Relate Solutions
-
Reservoir Level Monitoring
Real-time collection of reservoir water level, rainfall, and other information at dam monitoring points. Based on the changes in water level and the maximum capacity of the dam, calculations are made, and warnings and alarms are issued when the water level rises above the alert value.
more info... -
Pressure-release Pond Pipe Network Pressure Monitoring
The pressure-release pond can regulate the pressure of the water supply network. It adjusts the pipe network pressure by increasing or decreasing the water volume. The pond maintains the pipelines at a normal level. At various stages of the pressure-release pond, different instruments need to be installed.
more info... -
Irrigation Pipeline Monitoring
Pipelines are the most common water transportation and irrigation facilities. During transportation, pipelines effectively reduce evaporation and leakage of water resources. Monitoring instruments measure accurately discharge flow. It is a crucial action of rational water resource allocation and reasonable water fee collection.
more info... -
Bridge Culvert Water Accumulation Level Monitoring
Real-time monitoring the low-ling areas, underpasses and bridge culverts. The current level and alarming messages are automatically displayed on the screen, such as “Passage”, “Allowing”, and “No entering”. The alarm will be triggered when the level is too high, aiming to ensure the personnel's safety.
more info...
Copyright © 2025 MICRO SENSOR CO., LTD
